37 replies to this topic

[HNB]

So I have this body coming in to me.


4f60ff0d by Hentai No Baka, on Flickr


c6efa623 by Hentai No Baka, on Flickr

Now I have this neck coming in.


$(KGrHqZ,!qQE+nLDu6lqBQGT(tf1Wg~~48_20 by Hentai No Baka, on Flickr


$T2eC16R,!)8E9s4l7cCdBQGT(y3M5g~~48_20 by Hentai No Baka, on Flickr


dsc03272o by Hentai No Baka, on Flickr

I have the toggle plate from my Kurt Jazzy and the three hole Jag plate and upper plate. This is going to be my goal for her:


Green Jaguar by Hentai No Baka, on Flickr

I already put a mini On/On toggle in the middle hole between where the 1meg volume and tone will go. It will be a coil splitter for the humbuckers. The Rollers will be both 500k and be connected to both pickups so I have the option to play with 1meg or 500k's. I am keeping the TOM on it most likley. The cut switch and rhythm switch are white On/On switches. Going to dowel the stop tail and add a normal trem route.

Pickups are PAF and Super Distortion from my Cobain Jazzy project.

[HNB]

Chrome 70's F tuners ordered, 70's F neckplate and screws ordered, and new roller string tree ordered. Neck is set.

[The Jagmaster]

awesome!

[HNB]

I got paint today. This amount should (SHOULD) be enough to do the whole thing as long as I avoid any oops moments.


DSC05205 by Hentai No Baka, on Flickr


DSC05203 by Hentai No Baka, on Flickr

Thanks to my little son for loaning me one of his cars to help me color match the green.


DSC05204 by Hentai No Baka, on Flickr

[HNB]

The body came today. The paint finish wasn't as bad as the pictures I was given seemed. It was blue. It looked pretty nice actually aside from some runs on the front and back.


DSC05235 by Hentai No Baka, on Flickr

There was some very dry tape in the pickup areas and neck pocket.


DSC05236 by Hentai No Baka, on Flickr


DSC05237 by Hentai No Baka, on Flickr

Took her out to the garage when kids went down to nap and got to work stripping the body.

The front took two hours. There is still sealer I need to sand off.


DSC05241 by Hentai No Baka, on Flickr

The back took fourty-five minutes. (Go figure. LOL)


DSC05242 by Hentai No Baka, on Flickr


DSC05243 by Hentai No Baka, on Flickr

Still need to do the edges, but I will save that for tomorrow. Kids woke up and my hands and wrists are worn out from scraping. LOL

Tuners came in!


DSC05244 by Hentai No Baka, on Flickr

I will use my Jazzmaster template to draw out the tremolo space once I get the body sanded and stop tail holes doweled.


DSC05245 by Hentai No Baka, on Flickr

[HNB]

The body is done being stripped. I just need to finish hand sanding all the remaining crap (sealer and paint bits) before I can work on filling those stop tail holes and getting a normal tremolo routed.


DSC05246 by Hentai No Baka, on Flickr


DSC05247 by Hentai No Baka, on Flickr


DSC05251 by Hentai No Baka, on Flickr


DSC05252 by Hentai No Baka, on Flickr

[HNB]

The sides are sanded and smooth all the way around. My wife is getting me some sandpaper for my palm sander to do the front and back. I did the sides all by hand.


DSC05259 by Hentai No Baka, on Flickr


DSC05258 by Hentai No Baka, on Flickr

(Put some of my parts on for fun. )


DSC05256 by Hentai No Baka, on Flickr

[paltic]

looking good chris...

[HNB]

Thanks!! I glued dowels in to the stop tail holes. Once the glue dries I will cut them flat to the body. When I sand the top it will give me the chance to sand it nice and flat. I also used my template to mark about where the trem will go.


DSC05261 by Hentai No Baka, on Flickr

[HNB]

Ladies and gentlemen, we have a tremolo rout.


DSC05266 by Hentai No Baka, on Flickr

First I drilled a bunch of holes to help clear out some of the wood. (I drilled 1.25 inches down so I wouldn't accidentally go too deep.)


DSC05262 by Hentai No Baka, on Flickr

I routed the upper layer with my bit and then lowered it to 1 3/8 to get it to the correct depth.


DSC05267 by Hentai No Baka, on Flickr


DSC05268 by Hentai No Baka, on Flickr

Not bad for eye ball routing! (I have bad luck with templates so I just do it by eye.) I used a chisle to sharpen the lower corners.

[HNB]

I used the template I have and drilled holes for the trem. (I figured might as well do it before painting so I won't need to risk messing or marking up the paint finish.)


DSC05272 by Hentai No Baka, on Flickr


DSC05273 by Hentai No Baka, on Flickr

Then I went to work sanding the body.


DSC05275 by Hentai No Baka, on Flickr


DSC05276 by Hentai No Baka, on Flickr


DSC05281 by Hentai No Baka, on Flickr


DSC05283 by Hentai No Baka, on Flickr

Put some of the parts on to see how it looks. Not too bad.


DSC05284 by Hentai No Baka, on Flickr

[HNB]

Put some masking tape in to the TOM holes so I could seal without worrying about Z-Poxy going in to the holes.


DSC05285 by Hentai No Baka, on Flickr

Coat one of Z Poxy!


DSC05286 by Hentai No Baka, on Flickr


DSC05288 by Hentai No Baka, on Flickr


DSC05291 by Hentai No Baka, on Flickr

[HNB]

Got the third coat on. After it dries later I will lightly sand it and check to see if it is flat. If it looks good, I will work on the back next.


DSC05296 by Hentai No Baka, on Flickr


DSC05297 by Hentai No Baka, on Flickr

[HNB]

The neck arrived today. It looks good. The tuners were slightly larger than the holes so I had to enlarge them a little bit for the bushings and posts to fit. (Very scary drilling the holes bigger...) Fortunately it all went well. The roller is on as well.


DSC05330 by Hentai No Baka, on Flickr


DSC05332 by Hentai No Baka, on Flickr


DSC05333 by Hentai No Baka, on Flickr

Only issue is since it is a US neck and the body is Japanese, the pocket is a little too big. I understand it makes no difference, so I am not too worried about it.


DSC05337 by Hentai No Baka, on Flickr


DSC05338 by Hentai No Baka, on Flickr

[HNB]

Front is done.


DSC05340 by Hentai No Baka, on Flickr

First coat on the back is done.


DSC05341 by Hentai No Baka, on Flickr


DSC05342 by Hentai No Baka, on Flickr

[HNB]

More coats of sealer on the back.


DSC05384 by Hentai No Baka, on Flickr


DSC05387 by Hentai No Baka, on Flickr

[HNB]

Got it all taped off and ready to paint.


DSC05393 by Hentai No Baka, on Flickr

First coat of white on it for primer.


DSC05395 by Hentai No Baka, on Flickr


DSC05396 by Hentai No Baka, on Flickr


DSC05398 by Hentai No Baka, on Flickr


DSC05402 by Hentai No Baka, on Flickr


DSC05403 by Hentai No Baka, on Flickr


DSC05404 by Hentai No Baka, on Flickr


DSC05405 by Hentai No Baka, on Flickr

[HNB]

I wetsanded the first coat of primer. I am hoping that will help the second go on really flat so the metallic paint will look awesome. It is ready to paint now. I will spray coat two tomorrow. I should know then if I need to do a third coat or not to get it smooth.


DSC05409 by Hentai No Baka, on Flickr


DSC05410 by Hentai No Baka, on Flickr


DSC05411 by Hentai No Baka, on Flickr

[HNB]

Got coat number two on. It will need a third and maybe fourth coat because I can still see where the stop tail plugs are a little bit. My OCD wants that flat.


DSC05412 by Hentai No Baka, on Flickr


DSC05415 by Hentai No Baka, on Flickr


DSC05416 by Hentai No Baka, on Flickr


DSC05419 by Hentai No Baka, on Flickr


DSC05420 by Hentai No Baka, on Flickr

[HNB]

So there was still a little bit of line showing from the plugs showing so I sprayed some of the paint in to a lid and dabbed it on the spots. Once dry, I will sand it flat. I also dabbed a couple spots on the bottom so I can get it a bit more flat.


DSC05421 by Hentai No Baka, on Flickr


DSC05423 by Hentai No Baka, on Flickr